Jump to content


Mellow Yellow


  • Please log in to reply
62 replies to this topic

#51 ChevyJoe

ChevyJoe

    Advanced Member

  • Members
  • PipPipPip
  • 1,448 posts
  • LocationYakima, WA

Posted 10 October 2016 - 10:02 PM

I love both pairs of the twisted stitch seats I have

#52 R.DesJardin

R.DesJardin

    Advanced Member

  • Members
  • PipPipPip
  • 295 posts
  • LocationClarkston,WA

Posted 11 October 2016 - 02:13 PM

View PostChevyJoe, on 10 October 2016 - 10:02 PM, said:

I love both pairs of the twisted stitch seats I have

Are they suspension seats? And do you guys run adjusters? What kind, was thinking I wanted it so me, my wife and granddaughter could all drive.

Edited by R.DesJardin, 11 October 2016 - 04:55 PM.


#53 Jay W

Jay W

    Advanced Member

  • Members
  • PipPipPip
  • 1,529 posts
  • LocationYakima, WA

Posted 11 October 2016 - 06:25 PM

No adjusters for me. Happy with my PRPs.

#54 Tryan100

Tryan100

    Advanced Member

  • Members
  • PipPipPip
  • 1,228 posts
  • LocationYakima

Posted 11 October 2016 - 09:05 PM

I am cheap but I really like my corbeau baja ss seats.  I run no adjusters.  I haven't spent much time in other seats so I have nothing to really compare them to.

#55 R.DesJardin

R.DesJardin

    Advanced Member

  • Members
  • PipPipPip
  • 295 posts
  • LocationClarkston,WA

Posted 12 October 2016 - 01:25 PM

Corbeau Baja RS on the way. It's a 2dr and I have a little kid to haul around in the back seats. Not sure if of the rear seat setup yet.

#56 R.DesJardin

R.DesJardin

    Advanced Member

  • Members
  • PipPipPip
  • 295 posts
  • LocationClarkston,WA

Posted 18 October 2016 - 07:02 AM

Radiator has been the focus, I think I'm there, well close to it. Top bracket is 18ga steel and I plan on some bead rolls to reinforce it. There is room in front on the drivers side for my trans cooler. This all fits tight but I don't for see too many issues. Radiator hoses might be a bit of a challenge. But I will figure it out.
Posted Image

#57 R.DesJardin

R.DesJardin

    Advanced Member

  • Members
  • PipPipPip
  • 295 posts
  • LocationClarkston,WA

Posted 28 October 2016 - 08:53 PM

No its not tight at all. Now to find radiator hoses to fit.
Posted Image

#58 superglock

superglock

    Advanced Member

  • Members
  • PipPipPip
  • 180 posts
  • LocationSelah

Posted 29 October 2016 - 01:25 PM

What size radiator is that and who's is it. I have had a couple of sets of Mastercratf  seats and have been very happy.

#59 R.DesJardin

R.DesJardin

    Advanced Member

  • Members
  • PipPipPip
  • 295 posts
  • LocationClarkston,WA

Posted 01 November 2016 - 05:13 AM

View Postsuperglock, on 29 October 2016 - 01:25 PM, said:

What size radiator is that and who's is it. I have had a couple of sets of Mastercratf  seats and have been very happy.

Its a Novak XJ-LS swap radiator. Spal fans.

Worked on getting a powered unit adapted to the bead roller. and built some seat tabs. Then bent up one of the lower tubes for my cage design, I used BendTech and the tube came out perfect. 6 bends in one tube.
Seats are here so I had to set on in place on a tool box so I could get the look.
Posted Image Posted Image

Posted Image Posted Image

#60 R.DesJardin

R.DesJardin

    Advanced Member

  • Members
  • PipPipPip
  • 295 posts
  • LocationClarkston,WA

Posted 27 November 2016 - 07:35 AM

I hate it when you are bend tube and you bump the POB and lose where you are. Can you can repurposed bent tube.

#61 R.DesJardin

R.DesJardin

    Advanced Member

  • Members
  • PipPipPip
  • 295 posts
  • LocationClarkston,WA

Posted 06 February 2017 - 04:38 PM

3 seats. Back one is a PRP lite to fit my granddaughter.
Posted Image

#62 R.DesJardin

R.DesJardin

    Advanced Member

  • Members
  • PipPipPip
  • 295 posts
  • LocationClarkston,WA

Posted 04 March 2017 - 06:02 PM

Shifters in position and getting the cage to come together.
Posted Image Posted Image

#63 R.DesJardin

R.DesJardin

    Advanced Member

  • Members
  • PipPipPip
  • 295 posts
  • LocationClarkston,WA

Posted 05 March 2017 - 04:59 PM

Ready for some cross bracing and gussets.
Posted Image